Robust C9T Electric Fan Heater

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Details

The Robust C has been developed specifically for wall mounting in corrosive environments such as car wash facilities, sewage treatment plants and industrial plants. The Robust C is of hose-proof design to degree of protection IP65.

• Approved for use in humid and corrosive environments

• Casing, heater elements and grille of acid-resistant stainless steel to EN 1.4404

• Legs/stand are made of stainless steel

• All models suitable for mobile applications or wall

mounting

• Degree of protection IP65 - dust-tight and hose-proof

Design

The casing, heater elements and grille are made of acid-resistant stainless steel to EN 1.4404, and the legs/wall bracket of stainless steel to EN 1.4301. Built-in thermostat and output selector switch. Connection to the power supply by means of plug/socket (not 230V~, 230V3~ and 500V3~). Degree of protection IP65 (dust-tight and hose-proof ).

Accessories

An external type RTC/RTC4 control box with degree of protection IP65 can be connected to the Robust C.

Model	W	V	Art. No.
C9T	9000	500V3~	401265

Out of stock

Additional Details

Additional Details
Delivery	Dependant on stock availability. Check with us before ordering
Brand	Veab
Warranty	1 year warrenty in compliance with ORGALIME S2000

Robust_2020.pdf (4.8MB)

Heat Load	Watts	BTU
Average The Room Is A Normal Residential Room, Office, Reception Area Or Similar, Where There Is Not Overly Crowded With People, Computer And Office Equipment.
Above Average There Are Factors That Contribute To Additional Heat Being Generated In The Room E.G. Strong Lighting, Overcrowding With People And Office Equipment, Conservatory Type Room, Or Flat Roofed Room.
High There Are Factors That Contribute To A High Heat Load In The Room. E.G. Commercial Cooking, Much Computer And Server Equipment, Switchgear, Temporary Building With Thin Walls And Flat Room, Plain Glass Conservatory.

Variable	Units	Notes/Guidance
System Airflow	M3/Hr	If you have it in cfm then multiply your cfm value by 1.7 to get m3/hr
Average Combined Pressure Drop Of Filters Of Higher Than F6 Efficiency	Pascals	F8 bag filters pressure drop - typical clean clean to dirty, 160 - 250 Pascals F9 compact filters pressure drop - typical clean to dirty, 160 - 350 Pascals H10 HEPA filter pressure drop - typical clean to dirty, 250 - 600 Pascals 9.8 Pascals = 1 mm wg, & 249 Pascals = 1 inch wg
Carbon Filters Pressure Drop	Pascals	For compact type carbons pressure drop between 100 - 150 Pa Bonded carbon panels typically 150 - 170 Pa Loose granular carbon panels typically 130 Pa
Annual Operational Hours	Hrs/Annum	8760 hours in a year If operating for 5 days a week, excluding public holidays, for 12 hrs/day = 3000 hrs
Cost Of Power	Pence Per Kwh	Huge variance in what different companies pay. heck your last bill to be sure, otherwise put in 10p
Fan Efficiency	(As Decimal Value, Eg 100%=1)	Would typically be around 60%, so if you don’t have specific information use 0.6
Fan Motor Efficiency	(As Decimal Value, Eg 100%=1)	Larger motors should be around 90%, so if you don’t have specific information use 0.9

The Total Average Pressure Drop Over Your Higher Efficiency Filters And/Or Carbon Filters Is;		Pascals
This Pressure Drop Is Costing In Energy Alone	£	Per year
It Is Probable That A Sanuvox In-Duct System Could Break Down The Biological, Chemical And Odourous Contaminants On This Air Flow For Between 16 And 25% Of This Running Cost	£	Lower energy cost estimate of an equivalent Sanuvox system (16%)
	£	Higher energy cost estimate of an equivalent Sanuvox system (25%)

Type Of Building	Kw Range		BTU Range
Sports Centres
Retail Premises
Office Premises
Small Industrial Unit
Medium Industrial Units
Larger Industrial Buildings
School/Community Halls
Churches

Room/building volume	m3
Temperature differential (deltaT °C)	°C

Get in Touch

Robust C9T Electric Fan Heater

Give Us a Call

Our Address

Leave a Message

General Enquiries

Technical Enquiries

Postal Address

Email Us